1URDC Relay Diversion Dump Charge Control Controller Regulator Wind Solar Hydro

DUMP CONTROLLERS - EVOLVED ($99.95 SRP)

UNIVERSAL RELAY DIVERSION CHARGE CONTROLLER

MODEL 1URDC-V5 (finale) 12V (Board Version 5.1.X)

For both EMRs (ElectroMechanical Relays)

and SSRs (Solid State Relays)

For Wind, Solar and Hydro

Now with 3-Stage When Using SSR's in Diversion/Dump Mode!

(See manual for use with different voltage LA Batteries)

DESCRIPTION

The Universal Relay Diversion Controller/Regulator is a low cost Microprocessor controlled Diversion/Dump type controller designed for the DIY (Do It Yourselfer). It is designed to switch up to 6 conventional automotive style electromechanical relays (EMR) directly with up to 800ma total coil current draw with up to 240A power handling capability.

Also unlike other controllers of this type of design, it will also control DC-DC Solid State Relays (SSR) in Legacy/Conventional (Dump) diversion mode or use a 2-Stage or Intelligent/Smart 3-Stage charge algorithm including a manual Equalization mode. It is theoretically able to directly switch up to 32 SSR's at 25ma each (untested). If using just 40 amp SSR's that adds up to a potential 1280A (2560A using 80 amp SSR's) power handling capability.

To keep cost down, this controller was designed for the DIY (Do It Yourselfer) and is the BOARD ONLY and does not include an enclosure. It can be mounted directly on a wall in a area protected from the environment or in a Optional or user supplied enclosure. To keep cost down and prevent unnecessary waste this manual is available in PDF format only (just printout what you need). The latest version of this manual is Free for DOWNLOAD HERE 1URDC_V5_1_Manual.pdf.  Please download and read before purchasing.

FEATURES

• The ability to Directly Switch up to 6 Electromechanical or 32+ DC-DC Solid State Relays

• Legacy Dump/Diversion/On-Off - Electromechanical or Solid State Relays

• 2-Stage - Dump/Diversion (using 20ms on - 20ms off or faster SSR's Only )

• 3-Stage - Dump/Diversion (using 10ms on - 10ms off or faster SSR's Only )

• Manual Equalization Mode (using 20ms on - 20ms off or faster SSR's Only)

• Extremely Low Power Consumption (≤ 10ma) in Standby/Monitoring

• Accurate Battery Voltage Tracking

• Switching Speeds Up To 50 On-Off Cycles Per Second When Using SSR's (≤50Hz)

• User Settable Dump/Diversion/On-Off/Absorb Voltage Set-point (13.1 to 15.1 Volts)

• User Settable Float Voltage Set-point (12.5 to 14.5 Volts 3-Stage using SSR's Only)

• User Settable Equalization Voltage Set-point (14.5 to 16.5 Volts using SSR's Only)

• Optional FLA Temperature Compensation -40°F(-40°C) to 140°F(60°C) .0168V per 1°F

• Optional SLA Temperature Compensation -15°F(-26°C) to 140°F(60°C) .012V per 1°F

• The Ability to Divert/Dump 800ma Directly for Very Small Systems

• Self Resetting Fuses (Separate Power and Microcontroller Section Fuses)

• Multicolored LED Status Indicator

• LED Relay Power/Active Indicator

• Test Button

• Voltage Limiter (limits Maximum voltages to Approx 14.8V Except Equalization mode)

• Reverse Polarity Protection

• Over Voltage Protection

• Over Current Protection

• Transient/Lightning/Surge Protection

SPECIFICATIONS

Specifications subject to change without notice.

Made in USA

Components-Rest of World

WARRANTY:

WindAndSunPower.com. Model 1URDC is warranted to be free of defects in material and workmanship for three years from the date of purchase. Failure to provide correct installation, operation or care for this product, in accordance with the instruction manual, will void the warranty. Product liability shall be limited to repair or replacement, at the discretion of the manufacturer. The manufacturer is not responsible for the labor or other charges necessitated by the removal, transportation, or re-installation of any defective product. Warranty does not cover damage due to, mishandling, abusive conditions, lightning, or exposure to weather. No specific claim of merchantability shall be assumed or implied beyond what is printed in this manual. No liability shall exist from circumstances arising from the inability to use this product, or it’s inappropriateness for any specific purpose. In all cases, it shall be the responsibility of the customer to insure a safe installation in compliance with local, state and national electrical codes.